Solvers/

Stress & Strength Analysis Workstation

CAE WORKSTATIONISO 6892-1ASME BPVC Section VIII Division 2 (Part 5 Design by Analysis)

Calculate von Mises equivalent stress, Mohr circle transformation, principal stresses, and structural safety factors under combined loading states.

Loading...
▸Formula · assumptions · example(ISO 6892-1 · ASME BPVC Section VIII Division 2 (Part 5 Design by Analysis) · FKM Guideline (Analytical strength assessment))

Formula

σ1,2=σx+σy2±(σx−σy2)2+τxy2,σvm=σ12−σ1σ2+σ22,τmax⁡=σ1−σ22\sigma_{1,2} = \frac{\sigma_x + \sigma_y}{2} \pm \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2}, \quad \sigma_{\text{vm}} = \sqrt{\sigma_1^2 - \sigma_1 \sigma_2 + \sigma_2^2}, \quad \tau_{\max} = \frac{\sigma_1 - \sigma_2}{2}

2D plane stress transformation via Mohr’s circle, principal normal stresses (σ1, σ2), maximum in-plane shear stress (τmax), and von Mises / Tresca equivalent yield failure criteria.

Assumptions

  • · Plane stress state (σz = 0, τxz = 0, τyz = 0) typical for thin plates, web panels, and free exterior component surfaces
  • · Homogeneous, isotropic, linear-elastic material behavior up to initial yield point Sy
  • · Distortion energy (von Mises) yield criterion applied for ductile structural metals (steel, aluminum, titanium)
REFERENCE WORKED EXAMPLE · TEXTBOOK BASELINE (NOT LIVE INPUT)
ASME BPVC Section VIII Div 2 / FKM Guideline / von Mises

Biaxial Plane Stress Transformation & von Mises Yield Verification

BASELINE STATUS: PASS(+33.3% safety margin above minimum code requirement (FoS 2.00 vs 1.50))

Transformation of orthogonal normal and shear stresses into principal stresses and evaluation of multi-axial yielding against S355 structural steel.

1. Inputs & Boundary Parameters
Normal stress σx (tensile)120.0 MPa
Normal stress σy (compressive)-40.0 MPa
In-plane shear stress τxy60.0 MPa
Material gradeS355 Structural Steel EN 10025-2
Yield strength Sy355.0 MPa
Required safety factor nreq1.50 [-]
2. Applied Governing Equations & Standards
Average Normal Stress:
σavg=(σx+σy)/2σavg = (σx + σy) / 2
Mohr Center
Mohr Circle Radius:
R=√[((σx−σy)/2)2+τxy2]R = √[ ((σx - σy) / 2)² + τxy² ]
Maximum In-Plane Shear
Principal Stresses:
σ1=σavg+R,σ2=σavg−Rσ1 = σavg + R, σ2 = σavg - R
Principal Planes
von Mises Equivalent Stress:
σvm=√(σ12−σ1⋅σ2+σ22)σvm = √(σ1² - σ1·σ2 + σ2²)
Distortion Energy Theory
Yield Safety Factor:
FoS=Sy/σvmFoS = Sy / σvm
Elastic Margin
3. Intermediate Calculation Stages
Hydrostatic average stress σavg40.0
Mohr circle radius R (τmax)100.0
Major principal stress σ1140.0
Minor principal stress σ2-60.0
von Mises equivalent stress σvm177.8
4. Reference Benchmark Verification & Acceptance ThresholdBENCHMARK: PASS
von Mises Stress σvm & Safety Factor FoS: σvm = 177.76 MPa | FoS = 2.00
Acceptance limit: FoS ≥ 1.50 (σvm ≤ 236.7 MPa)